Terminaux de Paiements Intégrés (Cluster)

Terminaux S1F2 Mode Comptoir
  
 https://scribehow.com/viewer/Setting_Up_The_S1F2_on_Counter_Mode__q9m97rQlSI-09oul8UxN3A 
   
   
   
   
 a completer** 
 
  The S1F2 terminal is our wireless solution. This terminal can be set up on both counter service and Tableside simultaneously. 
 
 Before attempting to setup the S1F2, fully charge the battery. This can take 3-4 hours for the initial charging 
   
 2. On the backside of the terminal, you will see a sticker that notes down the serial number of the terminal. This will be the terminal identifier when reaching out to support. 
   
 
 3. On the left hand side of the terminal, there is a rubber flap covering the charging port. If not charging on the doc, the terminal can be charged using the USB-C port. 
   
 4. To connect the terminal to the internet, click the settings button in the bottom left corner. You will be brought to a menu where you can select "Network" . Enter the admin pin 1234, and select "Wi-Fi" 
   
 5. You'll be brought to a list of networks. Select the network your POS is using, and enter in the password using the on-screen keyboard that appears. The network will appear at the top of the list with "Connected" underneath once properly on the network. 
 
 6. Now we need to note down the IP of the terminal. Click on the triangle in the bottom left until you are back in the Terminal Menu. From here select "Device Info" to find the IP.

Terminaux S1F2 Mode Table
https://scribehow.com/viewer/Setting_Up_The_S1F2_on_Tableside__kz3Yd22jQmukCC-nYS9QWg 
  

Terminaux V400C Mode Comptoir
https://scribehow.com/viewer/Setting_Up_The_V400C_on_Counter_Mode__0MXy62DvSoeqlK0mG9iDjg 
  

Moneris DX8000 & PAX A920 - Direct (Counter Integration)
*Procédure copier du Zoho de Cluster 
 
 NOTE: POS must be on 6.10.0.0 minimum for integration to work.  
 Works with DX8005 also! It has been tested. 
 
 Open the  Moneris  GO App 
 
 
 
 If it's Not there, you can install it from the PAXSTORE 
 
 
 
 On this page, the client must enter their  Moneris  Portal Credentials in order to Access General Settings, Tips settings or Standalone mode. 
 This will be their email and password they set up via the "Let's Get Started" email sent to them by  Moneris .  
 
 
 
 It'll bring you to this Page where they can make payments in Standalone mode, Press the 3 Lines on top left. 
 
 
 
 Press Settings 
 
 
 
 From here, you can setup Receipt, Tips, Tax and many settings. 
 Press Sync once completed. 
 
 
 
 Once done, Sign Out 
 
 
 
 
 On this screen, press the X. If there's no X, press the Circle Home Button at bottom of screen. 
 
 
 
 Open the Go Integrated App 
 
 
 
 From this screen, swipe from Left to Right in order to access Quick Service Settings 
 
 
 Default Password is 212324 
 
 Press Settings 
 
 
 
 Set Operational Mode to Direct 
 
 
 Then Press Wifi 
 Make sure you're Connected to the same Wifi as the POS 
 
 
 
 Press and hold on the Wifi Name and tap Modify Network 
 
 
 
 Check Advanced Settings, Scroll down, and set IP Settings to Static 
 
 
 
 Configure the Terminal's IP, Gateway, DNS, etc 
 And Save 
 
 
 
 If back on this screen, Press Save 
 
 
 
 After tapping SAVE, you may see this screen:  
 
 
 The client will need to enter their  Moneris  MID.  
 If they do not have it, you will need to contact  Moneris  with the client.  
 
 You should be back to the Quick Service Page 
 
 
 
 On POS Settings, Device 
 Set  MONERIS  Device, Set IP of the Terminal 
 
   
 
 Test by sending a Payment 
 If POS freezes, reboot and it should be good to go! 

Paymentree - Tip Before Tax
  
 Sur le PC 
   
 
 
 Fermez l'application PDV en sélectionnant le X blanc sur la page Réglages du PDV. 
 
 
 Recherchez et ouvrez le fichier de configuration Paymentree dans Windows. 
 
 
 Sélectionnez l’option DIVERS (Miscellaneous) 
 
 
 
 
 
 
 Cochez l’option Pourboire sur le montant avant taxes (Tip on pre-tax amount).  
 Decocher "Combine Payment/Tip/Surcharge" 
 Appuyez sur Quitter, puis encore une fois sur Quitter pour sortir de la CONFIGURATION. 
 
 
 
   
 ----- 
 Sur le Terminal 
 Sur l’écran d’accueil de l’application Paymentree sur votre terminal, glissez vers la gauche. 
 
 Appuyez sur l’icône des Réglages 🔧  
 
 
 Entrez le NIP administrateur et appuyez sur RÉGLAGES (Settings) (Par Default = 9999) 
 
 
 Appuyez sur RÉGLAGES DU POURBOIRE (Gratuity Settings) 
 
 Activez l’option Pourboire sur le montant avant taxes (Tip on pre-tax amount) , puis appuyez sur OK pour enregistrer et quitter.